Quantcast
Channel: Tips & Tricks - Repetier-Forum
Browsing latest articles
Browse All 20 View Live

Turn off heaters on print cancellaton

I found out the heaters stay on after cancelling a print.Personally, I want the printer to power off after I cancel a print. I might cancel it remote when I see there is something wrong.I added the...

View Article



Printer Going cold, losing X/Y Location... Double check alternative server.

Ive been troubleshooting my repetier server for about a week. Server is on a netbook (might as well be a ras pi...) and after 30 minutes on any print it would start printing over air or it would stop...

View Article

Image may be NSFW.
Clik here to view.

Voice controlled 3D printer with Google Assistant

Here is a suggestion for Repetier Server integration with Smart platforms like new Google Assistant currently only available at Google devices such as Pixel and Google Home.In future, there would be...

View Article

Stop RS boot into Pi prompt

RS0.80.2How do i get a Pi command prompt?

View Article

Alternate French translation for Repetier-Server 0.80.3 (Raspberry Pi version)

Hello dudes,The french translation supplied with Repetier-Server is incredibly bad, with a lot of lacks, misinterpretations, errors, errors of orthography ... It is mandatory to switch to english...

View Article


Local touchscreen on printer ?

Hi,My printer not being aside my computer I'd like to get a local control of basic stuffs (on/off heating bed and nozzle, basic move of bed and axes !). My Reprap i3 has an LCD display and one...

View Article

Looks goog but not right

My prints then self look pretty good but the bottom is not solid and the sides are not attached to the body. What am I doing wrong?

View Article

Controlling PiTFT Plus 3.5" 480x320 backlight

I'm using PiTFT Plus 3.5" 480x320 TFT Touch (ADA2441) display which has TFT backlight pin connected to the raspberry pi.When using a screensaver and after display goes blank, it still has the backlight...

View Article


Image may be NSFW.
Clik here to view.

Installation of Waveshare 3.5" (non-HDMI) LCD display / touchscreen on...

Hereby i want to share how to setup 3.5" LCD display (non-HDMI) based on latest Repetier Server Image (v8) for the Raspberry Pi.It took me several hours to get it working and hopefully it's also useful...

View Article


Settings of REPETIER

Dear FriendsThanks for your help! Now I have a new question:When I connect the printer (Geeetech i3C) to the PC, I can let filament leak in hand mode at both nozzles. The filament, however, runs very...

View Article

Image may be NSFW.
Clik here to view.

Setting up Adafruit 3.5" TFT w/ Repetier Server

After trying to setup Octoprint with a plugin called Octoprint TFT where you can control everything from a small touchscreen I realized the amount of aspirin needed to resurrect that plugin wasn't...

View Article

lua exaples

hi,are there examples awailable how to write lua modules for repetier server? maybe on github?

View Article

Upload to repetier from slic3r prusa edition

Hi,I made a simple script to upload to repetier server waiting for slic3r native implementation as for octoprint or duet.Script for Windows is the following :@echo offc:\Windows\System32\curl.exe -i -X...

View Article


Restart repetier-server and klipper use extcommands

I add inti /var/lib/Repetier-Server/database/extcommands.xml:        <command>                <name>Restart Repieter server</name>                <execute>sudo service...

View Article

GPIO INPUT/OUTPUT CONTROL

Good evening, I state that I am not very expert in codes. I would like to be able to configure three relays to control the enclosure light, a light that indicates that the printer is working (green...

View Article


Set z offset 3d printer

Hello, I installed the bltouch on my printer and when I try to do the calibration of the plate I can't say that after disabling the endstops with M211 S0 the Z axis, however, I can't make it go below 0...

View Article

Disconnecting kernal: reset high-speed USB device

Hallo zusammen,Sporadische disconnects verunmöglichen drucken aub Repertier Server.Konfiguration:Raspberry PI  3 mit Repetier Server 93.1Verbindung via USB zu Arduino Due (Native USB Port) und...

View Article


Best Practices When Upgrading Repetier-Server Raspberry Pi Image

I'm at the point where I'm about to upgrade from my current version of 0.91.2 to the new stable release of 0.94.1.  I want to ensure I keep all the custom settings that I have made to the server.  For...

View Article

Access through SAMBA and use Project folder and uploader folder throught...

Hello.Thank you for a wonderful experience in your Repetier Server. I use a server with 2 printers that I am printing my projects from and want to share a work-around (sort of) that works for me.I DO...

View Article

"Pause and Resume" Printer with Light Sensor Data

Hello! I am pretty new to messing around with 3d printers, but that's what I need to do... So please help me out here!I am working on a project where I control a 3d printer with Repetier connected...

View Article
Browsing latest articles
Browse All 20 View Live


Latest Images